Nurtured Clay

Workshop notes, cone 03 to cone 10

Wood ash glaze: working with a material that changes every batch

Cone 10 Body Stoneware Level Advanced Time 2 hours Filed 21 October 2026

Process parameters · Glaze

Clay body
Stoneware
Cone
Cone 10
Temperature
≈ 1305 °C
Difficulty
Advanced
Working time
2 hours
Published
21 October 2026

Tools

  • Two buckets reserved for ash washing
  • A tray for drying washed ash
  • A rolling pin or a mortar for breaking up ash lumps
  • 80 mesh sieve, plus a 40 mesh sieve for speckled work
  • Glaze hydrometer
  • Pyrometer and a firing log with the ash batch number
  • A photograph record of each ash batch's fired test tiles

Ash glazes are the oldest glazes in the world and the only ones where the main flux is something you can collect from your own fireplace. The catch is variability: wood ash is mostly calcium oxide, but the exact proportion depends on the tree species, the soil, the part of the tree that burned and how completely it burned. This recipe gives a working range and the procedure for dialling in a new batch.

Cross-section of a 15 cm form: rim 14 cm, belly 16 cm, foot 7 cm.
Vessel cross-section — Section drawn to the rim, belly, foot and height recorded for this entry.
H 15 · Ø14 / Ø16 / Ø7 cm

Base

A triaxial ash glaze for cone 10 reduction, using washed wood ash from a hardwood fire as the main flux. Ash is a variable material: every batch of ash is a slightly different flux, which is why the recipe is written as a range and the first firing of each new ash batch is a test.

Oxide and material charge
Material Parts Share
Washed Hardwood Ash 40 39.2%
Custer Feldspar 30 29.4%
EPK Kaolin 15 14.7%
Silica (SiO₂) 10 9.8%
Whiting (CaCO₃) 5 4.9%
Red Iron Oxide (Fe₂O₃) 2 2.0%
Total charge 102

Fired surface

A glossy, slightly milky green-brown with tiny ash specks and a texture that runs from smooth where the glaze is thick to dry and orange-peeled where it is thin. Where it pools it is a deep green; where it breaks on a rim it is a warm cream.

Collecting and washing the ash

Hardwood ash is better than softwood ash: it is higher in calcium and contains fewer of the soluble potassium salts that make a glaze foam and craze. Collect from a fire of oak, maple, ash or fruitwood. Do not use ash from a fire that burned painted wood, plywood, charcoal briquettes or treated timber — those bring in lead, zinc and heavy metals.

Wash the ash in a bucket: cover with three times its volume of water, stir, let it settle for two hours, and pour off the water. Repeat three times. The washing removes the soluble alkalis, which are what make unwashed ash glazes foam and pinhol, and it drops the flux strength by about 15 percent. Dry the washed ash on a tray before weighing it.

Adjusting the recipe to a new batch

Start with 40 parts ash and fire a test tile on the first firing of every new batch. If the glaze is a dry, unmelted matte, increase the ash to 45 and reduce the feldspar to 25. If it is over-fluxed and has run off the tile, reduce the ash to 35 and increase the kaolin to 18. Work in 5-part steps and record the result each time.

The ash also carries iron and trace manganese, which is why the recipe's own iron addition is only 2 percent. A dark-coloured ash will give a browner glaze at the same addition; a very pale ash will give something closer to a celadon. Keep a photograph of each batch of fired tests on the bucket.

Sieving and the speckle decision

Ash glazes can be sieved to 40 mesh for a heavy speckle, 80 mesh for a light speckle, or 100 mesh for a nearly smooth surface. The specks are unburnt carbon and insoluble mineral particles and they are the signature of an ash glaze, but too much speckle reads as a defect on a fine piece. Sieve to 80 for anything you intend to sell.

Crush the ash lightly with a rolling pin before sieving; ash from a cold fire is often in soft lumps that will not pass through the sieve at all and will fire as large pale blisters on the glaze.

Firing, and why ash likes a long firing

Ash glazes benefit from a slower firing than a standard recipe: they contain a lot of calcium and very little boron or alkali, so they need time at the top temperature to melt fully and heal the surface. Soak for 30 minutes at cone 10 rather than 15.

Fire in medium reduction. Ash glazes in oxidation are flat and often yellow-brown; reduction brings out the green-brown and the depth. The same slow cool that suits iron satin — four to six hours down to 900 degrees — also suits ash, and gives it the faint blue-green haze that appears in the pooled areas on a good firing.

Steps

  1. Collect hardwood ash only; no painted, treated or briquette ash.
  2. Wash the ash three times with three volumes of water each time, then dry it on a tray.
  3. Crush the dry ash lightly and sieve it to 80 mesh.
  4. Weigh the ash, feldspar, kaolin, silica, whiting and iron oxide and combine dry.
  5. Add water, mix for eight minutes and adjust to 1.44 specific gravity.
  6. Fire a test tile before committing a load, on the first firing of every new ash batch.
  7. Adjust ash in 5-part steps against the kaolin if the melt or the colour is off, and record each result.
  8. Apply to the main work at 1.0 mm and fire to cone 10 in medium reduction with a 30-minute soak.
  9. Cool over four to six hours to 900 degrees, then let the kiln fall naturally.

Where it goes wrong

  • Using ash from a fire that burned painted or treated wood. It carries heavy metals into a food surface.
  • Skipping the washing. Unwashed ash glazes foam, pinhole and craze badly.
  • Not testing a new ash batch. Ash varies enough between batches to move the melt point by a cone.
  • Sieving to 40 mesh on a fine piece. The speckle reads as a defect at that scale.
  • Firing in oxidation. The colour goes flat and yellow-brown.
Symptom and cause
Symptom Cause
Glaze did not melt, dry and matte the ash was under-fluxing for this batch; raise ash to 45 and lower feldspar to 25.
Glaze ran off the test tile the ash was over-fluxing; lower ash to 35 and raise kaolin to 18.
Heavy foaming and pinholing the ash was not washed, so soluble alkalis are still present.
Large pale blisters on the fired surface ash lumps that never passed the sieve; crush and re-sieve the batch.
Colour is flat yellow-brown fired in oxidation rather than medium reduction.

Recipe and schedule numbers here were recorded on the workshop’s own kiln. A different kiln, a different thermocouple position or a different clay batch will move the result, so treat every firing schedule as a starting point and keep your own log beside it.

Same cone — Cone 10

← All Glazes